Application
Built for hi-performance Pro street vehicles, Street rods, and limited racing.
No TV cable or Governor is required.
No vacuum lines or kick-down components are required.
Full manual valve body - Forward Shift pattern only.
Complete unit comes with detailed installation and wiring instructions.
http://www.fbperformance.com/page.asp?get=22&t=Top2
Features
-
Forward Shift Pattern only
-
Improved Oil Circulation
-
No "Engine Braking" in 1st and 2nd Gear
-
Maximum Torque and Thrust Capacity
-
Overdrive and optional Trans-brake functions are electrically activated.
-
Quick Shift Operation
-
Reverse Safety Feature is included for Trans-Brake
-
Trans-brake (optional) permits Max stall speed and has Instant release for full tree
-
Hi-Capacity Filter
Competition Components
-
Hi Performance Clutch Packs & High Energy Band
-
300M Input Shaft
-
(Optional) Internal Transbrake with electric activation
-
SFI Adapter Bellhousing included
-
Heavy Duty Intermediate Mech. Diode Assembly
-
Competition Hi-flow Manual Valve-body & High Pressure Regulator
-
Modified Front Pump Assembly w/Teflon Rings
-
Large Servo Assembly
Options
| -VSC | Variable Stall Control | $1,189.10 | $1,399.55 |
| -YK1 | H.D. Billet C-4 Yoke | $172.50 | $201.25 |
| -YK2 | H.D. Billet yoke (large O.D.) | $201.25 | $230.00 |
| -HHP3 | High HP Modification - 300M Direct Drum Assy | $591.10 | $695.75 |
| -RC | Overdrive Relay controller w/Auto Reset & Momentary PB switch | $172.50 | $204.70 |
| -TS | Transmission Shield - installed | $269.10 | $317.40 |
| -DP | Deep (alum.) Pan & Filter extension | $219.65 | $258.75 |
| -FPS | SFI 164 tooth Flexplate (specify balance-0, 28 or 50)...(specify 6 or 8 bolt hole crankshaft) | $269.10 | $317.40 |
| -TB | Trans-brake feature added to full manual valve body | $241.50 | $282.90 |
| -FP | 184 tooth FE flexplate | $149.50 | $175.95 |
| -CN | AOD to 4STB conversion - 4WD | $113.85 | $133.40 |
| -GS | HD Wide Ratio Gear Set (2.84/1.56/1.00/0.70) | $687.70 | $808.45 |
| -HHP5 | High HP Modification - Oversized 300M Direct Drum Assy | $833.75 | $980.95 |
| -LB | Shift Lever & Bracket Kit (for Aftermarket Shifters) | $143.75 | $171.35 |
| -HHP1 | Higher HP Internal Valvebody Modifications (for up to 1200 hp) | $353.05 | $415.15 |
| -DS | Dip Stick & Tube (cadmium plated w/ locking top - specify engine) | $79.35 | $93.15 |
| -CK | Cross-member Adapter Kit (Early Mustang 65-73) | $209.30 | $246.10 |
Pricing
| SS16104-S-BL |
4STB (non-lock-up) Ford (FE block)
Core Charge:
$218.00
| $3,482.55 | $4,098.40 |
Order Notes
Fill out the "Converter Application Form" to determine correct converter size &
stall rpm. All transmissions with converters and related equipment will ship by
Freight in a special container.
Converters
| 11" | Street/Strip (Non l/u only) | 2200 - 2800 RPMs | 375 | 350 | $591.10 | $695.75 |
| 10" | Street Strip | 2400 - 3800 RPMs | 650 | 575 | $951.05 | $1,117.80 |
| 9" | Full Race | 4000 - 6000 RPMs | 1000 | 900 | $1,189.10 | $1,399.55 |
| 10" | Full Race | 2800 - 5000 RPMs | 900 | 750 | $1,135.05 | $1,344.35 |
| 9" | Extreme Duty..(Turbo/Super Appl) | 3000 - 6000 RPMs | 1500 | 1200 | $1,550.20 | $1,823.90 |
What kind of transmission fluid should I use?
For Street and Street/Strip applications we only recommend the use of Ford type "F" Transmission fluid. For Extreme Duty applications we only recommend the use of ULX-110 type fluid. Both of these fluids are natural Petrolium based. Both of these fluids contain zinc which is the primary additive for proper lubrication for high performance transmissions. We do not recomend synthetic transmission fluids.
How much transmission fluid does my transmission take?
The transmission and torque convertor can take anywhere from 9 to 13 quarts of fluid. Most of the fluid is contained in the torque convertor. After installation of the transmission and convertor is complete, pour (4-5) quarts of transmission fluid into the transmission. Then place transmission into neutral, start engine, and quickly add transmission fluid until it reaches the full mark (pan rail level on most applications) on the dipstick. Shift transmission into reverse and let run approximately (3) minutes. Running in reverse (3) minutes will give any contaminants in the transmission, converter, cooler or lines a chance to settle into the transmission pan and not be introduced to the automatic shift control part of the valve body or governor, causing the shift valves to stick. For more details follow link. http://www.fbperformance.com/NewSite/page.asp?get=14&t=Bottom2
Why is the automatic transmission generally perfered over a stick shift transmission?
From a convenience stand point, most high performance automatic transmissions have the ability to be shifted manually or automatically. From an efficiency standpoint, today’s automatic transmissions incorporate a more efficient torque converter that is specifically built for each application. These torque converters have the ability to multiply the engines torque during the stall phase. A clutch on the other hand, simply is along for the ride by connecting the engines power to drive-line. All converters also have a built-in fluid dampening feature. For the higher horsepower applications the automatic transmission and converter combination is more often than not more durable and reliable than the clutch and standard gear box combination. We’ve found when doing conversions from stick to automatic in high performance vehicles that these cars generally drop from a half to three quarters of a second in elapsed time in the quarter mile.